Kernel development in NASM

Question about which tools to use, bugs, the best way to implement a function, etc should go here. Don't forget to see if your question is answered in the wiki first! When in doubt post here.
Post Reply
MikyBart
Posts: 10
Joined: Tue Sep 03, 2024 9:21 am
Libera.chat IRC: MikyBart

Kernel development in NASM

Post by MikyBart »

Hi everyone, I have a problem with interrupt management, below I insert the code.
It does not give errors but when calling a software interrupt (OX80) it does nothing.:

IDT.ASM:

Code: Select all

GLOBAL IDT_Build
IDT_Build:
    pusha64
	
    ; Build the IDT
	xor rdi, rdi 				; create the 64-bit IDT (at linear address 0x0000000000000000)
    mov rdi, IDT
	mov rcx, 32					; 32
	mov rsi, isr_vector_asm		; ISR list
	cld

make_exception_gates: 			; make gates for exception handlers
	mov rax, qword[rsi]
	push rax					; save the exception gate to the stack for later use
	stosw						; store the low word (15:0) of the address
	mov ax, 0x0800
	stosw						; store the segment selector
	mov ax, 0x8F00
	stosw						; store exception gate marker
	pop rax						; get the exception gate back
	shr rax, 16
	stosw						; store the high word (31:16) of the address
	shr rax, 16
	stosd						; store the extra high dword (63:32) of the address.
	xor rax, rax
	stosd						; reserved

	inc rsi						; next isr

	;push rsi
	;mov rsi, idt_install
	;call debug_msg
	;pop rsi
	
	dec rcx
	jnz make_exception_gates

	mov rcx, 256-32
	;mov rdi, IDT+32
	;mov rsi, isr_vector_asm+32

make_interrupt_gates: 			; make gates for exception handlers
	mov rax, qword[rsi]
	push rax					; save the exception gate to the stack for later use
	stosw						; store the low word (15:0) of the address
	mov ax, 0x0800
	stosw						; store the segment selector
	mov ax, 0x8E00
	stosw						; store exception gate marker
	pop rax						; get the exception gate back
	shr rax, 16
	stosw						; store the high word (31:16) of the address
	shr rax, 16
	stosd						; store the extra high dword (63:32) of the address.
	xor rax, rax
	stosd						; reserved

	inc rsi						; next isr

	;push rsi
	;mov rsi, isr_install
	;call debug_msg
	;pop rsi
	
	dec rcx
	jnz make_interrupt_gates

	; install the syscall handler
	push rbx
	xor rbx, rbx
	mov rsi, ISR_Syscall
	mov bx, 0x8F00
	mov rax, 127
	call IDT_Set_Gate
	pop rbx

	cli
	lidt [IDTR]
	sti

    popa64
    ret
IDT_SET_GATE:

Code: Select all

[code]IDT_Set_Gate:
	push rax
	push rdi
	push rcx
	push rbx
	push rsi

	mov rcx, rax				; save gate number
	mov rax, 16					; IDT address + gate number * 16
	mul rcx
	mov rdi, IDT
	add rdi, rax				; set correct position inside the IDT

	mov rax, rsi				; get the ISR address
	push rax					; save the exception gate to the stack for later use
	stosw						; store the low word (15:0) of the address
	mov ax, 0x2800
	stosw						; store the segment selector
	mov ax, bx
	stosw						; store exception gate marker
	pop rax						; get the exception gate back
	shr rax, 16
	stosw						; store the high word (31:16) of the address
	shr rax, 16
	stosd						; store the extra high dword (63:32) of the address.
	xor rax, rax
	stosd						; reserved

	mov rsi, gate
	call debug_msg

	pop rsi
	pop rbx
	pop rcx	
	pop rdi
	pop rax
	ret

SECTION .data
; The IDTR is the argument for the LIDT assembly instruction
; which loads the location of the IDT to the IDT Register. 
;ALIGN 4
IDTR:
  .Length dw 256*16-1 			; One less than the size of the IDT in bytes.
  .Base   dq IDT           		; The linear address of the Interrupt Descriptor Table 
                                ; (not the physical address, paging applies).
IDT: db 256*16-1 dup(0)[/code]

macros that create the interrupt list:

Code: Select all

%macro ISR_ERR 1
ISR%1:
	    ; error code is being pushed automatically by CPU (because "ERR")
    push %1 ; push isr number
    jmp isr_handler_asm
%endmacro

%macro ISR_NO_ERR 1
ISR%1:
    push 0  ; push error code by hand as not automatically done by CPU (because "NO_ERR")
    push %1 ; push isr number
    jmp isr_handler_asm
%endmacro
thanks for the help.
Octocontrabass
Member
Member
Posts: 5446
Joined: Mon Mar 25, 2013 7:01 pm

Re: Kernel development in NASM

Post by Octocontrabass »

MikyBart wrote: Tue Sep 03, 2024 9:29 amIt does not give errors but when calling a software interrupt (OX80) it does nothing.:
What kind of debugging have you tried so far?
MikyBart wrote: Tue Sep 03, 2024 9:29 am

Code: Select all

	mov rax, 127
	call IDT_Set_Gate
That's not 0x80.
MikyBart wrote: Tue Sep 03, 2024 9:29 am

Code: Select all

IDT: db 256*16-1 dup(0)
Your IDT is one byte larger than the space you're reserving for it.
MikyBart
Posts: 10
Joined: Tue Sep 03, 2024 9:21 am
Libera.chat IRC: MikyBart

Re: Kernel development in NASM

Post by MikyBart »

Sorry I didn't understand, the memory space for idt is shorter?
16 bytes each element multiplied by 256 minus one considering 0.
Octocontrabass
Member
Member
Posts: 5446
Joined: Mon Mar 25, 2013 7:01 pm

Re: Kernel development in NASM

Post by Octocontrabass »

MikyBart wrote: Tue Sep 03, 2024 1:07 pm16 bytes each element multiplied by 256 minus one considering 0.
That's how you calculate the limit, not the size. The limit is one less than the size.
Post Reply