Code: Select all
void _cdecl i86_flpy_irq () {
_asm add esp, 12
_asm pushad
_asm cli
//! irq fired
_FloppyDiskIRQ = 1;
//! tell hal we are done
interruptdone( FLOPPY_IRQ );
_asm sti
_asm popad
_asm iretd
}
Code: Select all
//** flpydsk.cpp
#include <hal.h>
#include "flpydsk.h"
/*
** Controller I/O Ports. Please see chapter for additional ports
*/
enum FLPYDSK_IO {
FLPYDSK_DOR = 0x3f2,
FLPYDSK_MSR = 0x3f4,
FLPYDSK_FIFO = 0x3f5,
FLPYDSK_CTRL = 0x3f7
};
/**
* Bits 0-4 of command byte. Please see chapter for additional commands
*/
enum FLPYDSK_CMD {
FDC_CMD_READ_TRACK = 2,
FDC_CMD_SPECIFY = 3,
FDC_CMD_CHECK_STAT = 4,
FDC_CMD_WRITE_SECT = 5,
FDC_CMD_READ_SECT = 6,
FDC_CMD_CALIBRATE = 7,
FDC_CMD_CHECK_INT = 8,
FDC_CMD_FORMAT_TRACK= 0xd,
FDC_CMD_SEEK = 0xf
};
/**
* Additional command masks. Can be masked with above commands
*/
enum FLPYDSK_CMD_EXT {
FDC_CMD_EXT_SKIP = 0x20, //00100000
FDC_CMD_EXT_DENSITY = 0x40, //01000000
FDC_CMD_EXT_MULTITRACK = 0x80 //10000000
};
/*
** Digital Output Register
*/
enum FLPYDSK_DOR_MASK {
FLPYDSK_DOR_MASK_DRIVE0 = 0, //00000000 = here for completeness sake
FLPYDSK_DOR_MASK_DRIVE1 = 1, //00000001
FLPYDSK_DOR_MASK_DRIVE2 = 2, //00000010
FLPYDSK_DOR_MASK_DRIVE3 = 3, //00000011
FLPYDSK_DOR_MASK_RESET = 4, //00000100
FLPYDSK_DOR_MASK_DMA = 8, //00001000
FLPYDSK_DOR_MASK_DRIVE0_MOTOR = 16, //00010000
FLPYDSK_DOR_MASK_DRIVE1_MOTOR = 32, //00100000
FLPYDSK_DOR_MASK_DRIVE2_MOTOR = 64, //01000000
FLPYDSK_DOR_MASK_DRIVE3_MOTOR = 128 //10000000
};
/**
* Main Status Register
*/
enum FLPYDSK_MSR_MASK {
FLPYDSK_MSR_MASK_DRIVE1_POS_MODE = 1, //00000001
FLPYDSK_MSR_MASK_DRIVE2_POS_MODE = 2, //00000010
FLPYDSK_MSR_MASK_DRIVE3_POS_MODE = 4, //00000100
FLPYDSK_MSR_MASK_DRIVE4_POS_MODE = 8, //00001000
FLPYDSK_MSR_MASK_BUSY = 16, //00010000
FLPYDSK_MSR_MASK_DMA = 32, //00100000
FLPYDSK_MSR_MASK_DATAIO = 64, //01000000
FLPYDSK_MSR_MASK_DATAREG = 128 //10000000
};
/**
* Controller Status Port 0
*/
enum FLPYDSK_ST0_MASK {
FLPYDSK_ST0_MASK_DRIVE0 = 0, //00000000 = for completness sake
FLPYDSK_ST0_MASK_DRIVE1 = 1, //00000001
FLPYDSK_ST0_MASK_DRIVE2 = 2, //00000010
FLPYDSK_ST0_MASK_DRIVE3 = 3, //00000011
FLPYDSK_ST0_MASK_HEADACTIVE = 4, //00000100
FLPYDSK_ST0_MASK_NOTREADY = 8, //00001000
FLPYDSK_ST0_MASK_UNITCHECK = 16, //00010000
FLPYDSK_ST0_MASK_SEEKEND = 32, //00100000
FLPYDSK_ST0_MASK_INTCODE = 64 //11000000
};
/*
** LPYDSK_ST0_MASK_INTCODE types
*/
enum FLPYDSK_ST0_INTCODE_TYP {
FLPYDSK_ST0_TYP_NORMAL = 0,
FLPYDSK_ST0_TYP_ABNORMAL_ERR= 1,
FLPYDSK_ST0_TYP_INVALID_ERR = 2,
FLPYDSK_ST0_TYP_NOTREADY = 3
};
/**
* GAP 3 sizes
*/
enum FLPYDSK_GAP3_LENGTH {
FLPYDSK_GAP3_LENGTH_STD = 42,
FLPYDSK_GAP3_LENGTH_5_14= 32,
FLPYDSK_GAP3_LENGTH_3_5= 27
};
/*
** Formula: 2^sector_number * 128, where ^ denotes "to the power of"
*/
enum FLPYDSK_SECTOR_DTL {
FLPYDSK_SECTOR_DTL_128 = 0,
FLPYDSK_SECTOR_DTL_256 = 1,
FLPYDSK_SECTOR_DTL_512 = 2,
FLPYDSK_SECTOR_DTL_1024 = 4
};
/**
* Constants
*/
//! floppy irq
const int FLOPPY_IRQ = 6;
//! sectors per track
const int FLPY_SECTORS_PER_TRACK = 18;
//! dma tranfer buffer starts here and ends at 0x1000+64k
//! You can change this as needed. It must be below 16MB and in idenitity mapped memory!
int DMA_BUFFER = 0x1000;
//! FDC uses DMA channel 2
const int FDC_DMA_CHANNEL = 2;
//! used to wait in miliseconds
extern void sleep (int);
//! current working drive. Defaults to 0 which should be fine on most systems
static uint8_t _CurrentDrive = 0;
//! set when IRQ fires
static volatile uint8_t _FloppyDiskIRQ = 0;
/**
* DMA Routines.
*/
bool _cdecl dma_initialize_floppy(uint8_t* buffer, unsigned length){
union{
uint8_t byte[4];//Lo[0], Mid[1], Hi[2]
unsigned long l;
}a, c;
a.l=(unsigned)buffer;
c.l=(unsigned)length-1;
//Check for buffer issues
if ((a.l >> 24) || (c.l >> 16) || (((a.l & 0xffff)+c.l) >> 16)){
#ifdef _DEBUG
_asm{
mov eax, 0x1337
cli
hlt
}
#endif
return false;
}
dma_reset (1);
dma_mask_channel( FDC_DMA_CHANNEL );//Mask channel 2
dma_reset_flipflop ( 1 );//Flipflop reset on DMA 1
dma_set_address( FDC_DMA_CHANNEL, a.byte[0],a.byte[1]);//Buffer address
dma_reset_flipflop( 1 );//Flipflop reset on DMA 1
dma_set_count( FDC_DMA_CHANNEL, c.byte[0],c.byte[1]);//Set count
dma_set_read ( FDC_DMA_CHANNEL );
dma_unmask_all( 1 );//Unmask channel 2
return true;
}
//! sets DMA base address
void flpydsk_set_dma (int addr) {
DMA_BUFFER = addr;
}
/**
* Basic Controller I/O Routines
*/
//! return fdc status
uint8_t flpydsk_read_status () {
//! just return main status register
return inportb (FLPYDSK_MSR);
}
//! write to the fdc dor
void flpydsk_write_dor (uint8_t val ) {
//! write the digital output register
outportb (FLPYDSK_DOR, val);
}
//! send command byte to fdc
void flpydsk_send_command (uint8_t cmd) {
//! wait until data register is ready. We send commands to the data register
for (int i = 0; i < 500; i++ )
if ( flpydsk_read_status () & FLPYDSK_MSR_MASK_DATAREG )
return outportb (FLPYDSK_FIFO, cmd);
}
//! get data from fdc
uint8_t flpydsk_read_data () {
//! same as above function but returns data register for reading
for (int i = 0; i < 500; i++ )
if ( flpydsk_read_status () & FLPYDSK_MSR_MASK_DATAREG )
return inportb (FLPYDSK_FIFO);
return 0;
}
//! write to the configuation control register
void flpydsk_write_ccr (uint8_t val) {
//! write the configuation control
outportb (FLPYDSK_CTRL, val);
}
/**
* Interrupt Handling Routines
*/
//! wait for irq to fire
inline void flpydsk_wait_irq () {
//! wait for irq to fire
while ( _FloppyDiskIRQ == 0)
;
_FloppyDiskIRQ = 0;
}
//! floppy disk irq handler
void _cdecl i86_flpy_irq () {
_asm add esp, 12
_asm pushad
_asm cli
//! irq fired
_FloppyDiskIRQ = 1;
//! tell hal we are done
interruptdone( FLOPPY_IRQ );
_asm sti
_asm popad
_asm iretd
}
/**
* Controller Command Routines
*/
//! check interrupt status command
void flpydsk_check_int (uint32_t* st0, uint32_t* cyl) {
flpydsk_send_command (FDC_CMD_CHECK_INT);
*st0 = flpydsk_read_data ();
*cyl = flpydsk_read_data ();
}
//! turns the current floppy drives motor on/off
void flpydsk_control_motor (bool b) {
//! sanity check: invalid drive
if (_CurrentDrive > 3)
return;
uint8_t motor = 0;
//! select the correct mask based on current drive
switch (_CurrentDrive) {
case 0:
motor = FLPYDSK_DOR_MASK_DRIVE0_MOTOR;
break;
case 1:
motor = FLPYDSK_DOR_MASK_DRIVE1_MOTOR;
break;
case 2:
motor = FLPYDSK_DOR_MASK_DRIVE2_MOTOR;
break;
case 3:
motor = FLPYDSK_DOR_MASK_DRIVE3_MOTOR;
break;
}
//! turn on or off the motor of that drive
if (b)
flpydsk_write_dor (uint8_t(_CurrentDrive | motor | FLPYDSK_DOR_MASK_RESET | FLPYDSK_DOR_MASK_DMA));
else
flpydsk_write_dor (FLPYDSK_DOR_MASK_RESET);
//! in all cases; wait a little bit for the motor to spin up/turn off
sleep (20);
}
//! configure drive
void flpydsk_drive_data (uint8_t stepr, uint8_t loadt, uint8_t unloadt, bool dma ) {
uint8_t data = 0;
//! send command
flpydsk_send_command (FDC_CMD_SPECIFY);
data = ( (stepr & 0xf) << 4) | (unloadt & 0xf);
flpydsk_send_command (data);
data = (( loadt << 1 ) | ( (dma) ? 0 : 1 ) );
flpydsk_send_command (data);
}
//! calibrates the drive
int flpydsk_calibrate (uint8_t drive) {
uint32_t st0, cyl;
if (drive >= 4)
return -2;
//! turn on the motor
flpydsk_control_motor (true);
for (int i = 0; i < 10; i++) {
//! send command
flpydsk_send_command ( FDC_CMD_CALIBRATE );
flpydsk_send_command ( drive );
flpydsk_wait_irq ();
flpydsk_check_int ( &st0, &cyl);
//! did we fine cylinder 0? if so, we are done
if (!cyl) {
flpydsk_control_motor (false);
return 0;
}
}
flpydsk_control_motor (false);
return -1;
}
//! disable controller
void flpydsk_disable_controller () {
flpydsk_write_dor (0);
}
//! enable controller
void flpydsk_enable_controller () {
flpydsk_write_dor ( FLPYDSK_DOR_MASK_RESET | FLPYDSK_DOR_MASK_DMA);
}
//! reset controller
void flpydsk_reset () {
uint32_t st0, cyl;
//! reset the controller
flpydsk_disable_controller ();
flpydsk_enable_controller ();
[color=red]flpydsk_wait_irq ();[/color]
//! send CHECK_INT/SENSE INTERRUPT command to all drives
for (int i=0; i<4; i++)
flpydsk_check_int (&st0,&cyl);
//! transfer speed 500kb/s
flpydsk_write_ccr (0);
//! pass mechanical drive info. steprate=3ms, unload time=240ms, load time=16ms
flpydsk_drive_data (3,16,240,true);
//! calibrate the disk
flpydsk_calibrate ( _CurrentDrive );
}
//! read a sector
void flpydsk_read_sector_imp (uint8_t head, uint8_t track, uint8_t sector) {
uint32_t st0, cyl;
//! initialize DMA
dma_initialize_floppy ((uint8_t*) DMA_BUFFER, 512 );
//! set the DMA for read transfer
dma_set_read ( FDC_DMA_CHANNEL );
//! read in a sector
flpydsk_send_command (
FDC_CMD_READ_SECT | FDC_CMD_EXT_MULTITRACK | FDC_CMD_EXT_SKIP | FDC_CMD_EXT_DENSITY);
flpydsk_send_command ( head << 2 | _CurrentDrive );
flpydsk_send_command ( track);
flpydsk_send_command ( head);
flpydsk_send_command ( sector);
flpydsk_send_command ( FLPYDSK_SECTOR_DTL_512 );
flpydsk_send_command ( ( ( sector + 1 ) >= FLPY_SECTORS_PER_TRACK ) ? FLPY_SECTORS_PER_TRACK : sector + 1 );
flpydsk_send_command ( FLPYDSK_GAP3_LENGTH_3_5 );
flpydsk_send_command ( 0xff );
//! wait for irq
flpydsk_wait_irq ();
//! read status info
for (int j=0; j<7; j++)
flpydsk_read_data ();
//! let FDC know we handled interrupt
flpydsk_check_int (&st0,&cyl);
}
//! seek to given track/cylinder
int flpydsk_seek ( uint8_t cyl, uint8_t head ) {
uint32_t st0, cyl0;
if (_CurrentDrive >= 4)
return -1;
for (int i = 0; i < 10; i++ ) {
//! send the command
flpydsk_send_command (FDC_CMD_SEEK);
flpydsk_send_command ( (head) << 2 | _CurrentDrive);
flpydsk_send_command (cyl);
//! wait for the results phase IRQ
flpydsk_wait_irq ();
flpydsk_check_int (&st0,&cyl0);
//! found the cylinder?
if ( cyl0 == cyl)
return 0;
}
return -1;
}
//! convert LBA to CHS
void flpydsk_lba_to_chs (int lba,int *head,int *track,int *sector) {
*head = ( lba % ( FLPY_SECTORS_PER_TRACK * 2 ) ) / ( FLPY_SECTORS_PER_TRACK );
*track = lba / ( FLPY_SECTORS_PER_TRACK * 2 );
*sector = lba % FLPY_SECTORS_PER_TRACK + 1;
}
//! install floppy driver
void flpydsk_install (int irq) {
//! install irq handler
setvect (irq, i86_flpy_irq);
//! reset the fdc
flpydsk_reset ();
//! set drive information
flpydsk_drive_data (13, 1, 0xf, true);
}
//! set current working drive
void flpydsk_set_working_drive (uint8_t drive) {
if (drive < 4)
_CurrentDrive = drive;
}
//! get current working drive
uint8_t flpydsk_get_working_drive () {
return _CurrentDrive;
}
//! read a sector
uint8_t* flpydsk_read_sector (int sectorLBA) {
if (_CurrentDrive >= 4)
return 0;
//! convert LBA sector to CHS
int head=0, track=0, sector=1;
flpydsk_lba_to_chs (sectorLBA, &head, &track, §or);
//! turn motor on and seek to track
flpydsk_control_motor (true);
if (flpydsk_seek ((uint8_t)track, (uint8_t)head) != 0)
return 0;
//! read sector and turn motor off
flpydsk_read_sector_imp ((uint8_t)head, (uint8_t)track, (uint8_t)sector);
flpydsk_control_motor (false);
//! warning: this is a bit hackish
return (uint8_t*) DMA_BUFFER;
}
